PDS_VERSION_ID = 3 LABEL_REVISION_NOTE = "2004-09-29, YL first draft" RECORD_TYPE = STREAM RELEASE_ID = 0001 REVISION_ID = 0000 OBJECT = INSTRUMENT INSTRUMENT_HOST_ID = MEX INSTRUMENT_ID = OMEGA OBJECT = INSTRUMENT_INFORMATION INSTRUMENT_NAME = "Observatoire Mineralogie, Eau, Glaces, Activite" INSTRUMENT_DESC = " Instrument Overview =================== OMEGA is a mapping spectrometer working both in the visible and the infrared spectral ranges. It is made of two co-aligned channels, one working in the 0.38 to 1.05 micrometers visible and near infrared range (VNIR channel), the other in the 0.93 to 5.1 micrometers short wavelength infrared range (SWIR channel). The data products constitute three-dimensional (X,Y,lamda) image-cubes, with two spatial and one spectral dimensions. The VNIR channel uses a bi-dimensional CCD detector, operated in a pushbroom mode. Its telescope acquires at once in its focal plane one cross-track line corresponding to the entire 8.8 degrees FOV, defined by an entrance slit; the second dimension of the image is provided by the motion of the S/C. Each line is spectrally dispersed along the columns of the array, the slit being imaged through a concave holographic grating. The SWIR channel operates in the whiskbroom mode: each imaged pixel is acquired at once by an IR telescope; a scanning mirror, in front of the telescope, permits to acquire crosstrack swaths of 16 up to 128 pixels width, for a maximum FOV of 8.8 degrees, thus matching the VNIR FOV, while the S/C motion provides the second spatial dimension. The imaged pixel is focused by the telescope on a slit, followed by a collimator. The beam is then split towards two separated spectrometers, to acquire the IR spectrum of each resolved pixel onto two InSb linear arrays of 128 spectels each, from 0.93 to 2.73 micrometers and from 2.55 to 5.1 micrometers respectively. Each array is cooled down 70K by a dedicated cryocooler, while the entire spectrometer is cooled down 190 K by a conductive link to a passive radiator. The typical IR integration time, defined by the S/C ground track velocity and the spatial sampling chosen, is 5 msec. The corresponding VNIR integration times are 100 to 800 ms, depending on the swath width, thus the altitude. With such integration times, SNR > 100, over the entire spectral range, is the specification. OMEGA is made of two distinct units: - a Camera unit (OMEGA-C) with the VNIR and SWIR spectrographs, their associated electrical devices, and one electronics assembly for the control of the camera. All units are integrated onto a common base plate; its mass is 23.8 kg. - a Main Electronics module (OMEGA-ME), for the data processing and the general management of the instrument; its mass is 5.1 kg. VNIR spectrograph ----------------- VNIR is made of two optical subsystems: a focusing telescope with its focal plane on a slit, and a spectrometer, that spreads the slit image in the spectral dimension. It provides image data in the spectral range 0.38 to 1.05 micrometers achieving a maximum spatial sampling of 0.4 mrad and a maximum spectral sampling of 50 Angstrom. A refractive telescope focuses the image on a slitplaced on the Rowland circle of an aberration corrected concave holographic grating mirror. This element reflects and disperses the light on a CCD detector tangent to the Rowland circle. The detector used is the TH7863 frame transfer CCD produced by Thomson. The chosen grating mirror can create a flat image onto the focal plane. This property allows to match very well the flat detector matrix to the grating, without other optical components. A CCD frame is then composed of N rows each containing an image of the slit at a given wavelength, and M columns each containing the spectrum of a point along the slit. The bi-dimensional image of the surface is obtained by the pushbroom technique, in which the spacecraft movement along its orbit performs a scan of the slit across the planetary surface. The electrical signal from the detector is amplified and then digitized by a fast 12 bit A/D converter; after conversion, all data are processed within the OMEGA-ME. In order to decrease the detector noise, VNIR is cooled down 190 K by conduction to the SWIR mechanical unit. The choice of refractive over reflective optics was made because of the large (8.8 degrees) field of view requirement. The telescope has a 6 elements objective similar to that of a modern commercial photographic camera. The shape of the elements and the types of optical glass were chosen to obtain the best chromatic aberration corrections over the entire spectral range. The last element serves as a field lens which matches the entire objective with the grating to avoid light losses. To avoid stress in the lenses at the working temperature, the two doublets are not cemented. The two glasses, FK54 and fused silica, have very different expansion coefficients of 8 and 0.55 x 10E-6/K at room temperature. The entrance aperture of 15.6 mm is defined by a diaphragm between the two doublets. An aberration corrected concave holographic grating is placed 142.7 mm from the entrance slit (which is in the focal plane of the telescope). The grating is tilted to form the spectrum at an angle of roughly 6 degrees from the optical axis. This angle does not allow CCD insertion near the entrance without beam obscuration; therefore, a folding mirror deflects the beam toward the side of the assembly, where the CCD can be mounted with ample clearance The zero order spectrum, at 4.5 degrees from the folded optical axis (lying in the y-z plane) is directed into a light trap to prevent degradation of the image. The first order spectrum ranges in angle from 6 degrees at lamda = 0.35 micrometers to 10 degrees for lamda = 1.05 micrometers. The second and higher order spectra can, in principle, also degrade the data. Its contribution depends both on the grating efficiency, and the spectral distribution of the incident radiation. For this reason, a dedicated filter is mounted, in front of the detector. The concave, spherical, holographic grating in a Rowland mounting - where the entrance slit and the spectrum are on radii of curvature of the grating - makes the spectrometer compact, light, and simple. In fact, no collimator or camera lens is required and the spectrometer has only one element. Moreover, the focal plane image can be flat, to match the planar CCD sensors. Since the concave holographic grating is obtained by recording a perfect optical pattern with groove spacing absolutely constant, it has no ghosts. Stray light has also a much lower level than the best ruled gratings. Therefore, concave holographic gratings generally have a much higher signal to noise ratio than classically ruled gratings. The optical performances have been computed by ray tracing. In the focal plane the spot diagram is about the pixel size (23x23 microns). For off-axis propagation (4.4 degrees off-axis), the total spot size is about 2 pixels in the sagittal direction. More precisely, on axis and at 0.7 micrometers, 98.8 % of the energy falls within a 23x23 micron pixel; at 4.4 degrees off-axis and lamda = 0.4 micrometers, 74 % of the energy falls within a CCD element. When the light propagates off-axis, the spot size is smaller for the shorter wavelengths. The Pattern Generator (PG) determines the CCD integration time, and generates the timing signals necessary to transfer an image from the light sensitive area to the masked zone and then to the output shift register of the CCD. The output of the CCD is then amplified and converted by a fast 12 bit A/D converter under control of the PG. The timing of the instrument imposes a relatively high frequency for CCD operation. In fact, depending on the distance from the planet and hence on the spacecraft speed, the time TR between consecutive frames can be chosen as: 100, 200, 400 or 800 ms. During the TR period the integration, readout and data transmission processes must occur. To save time, integration and transmission of the previous frame are overlapped. Because the maximum data value which can be transmitted during TR is limited to 12288 bytes, it is not possible to read the total frame of 384x288 pixels, corresponding to 110592 bytes. We are forced to read only a sub-frame, or to reduce the number of pixels by summing them on chip. The combination of different scientific requirements, integration times and hardware limitations led us to the definition of 40 operation modes, which can be selected through commands sent to the spacecraft, ranging from the nominal (spatial x spectral) mode (128x96 with summation of 3x3 pixels), to the high spectral resolution mode (64x144), to the high speed mode (16x96). Summation along columns and rows will decrease the spatial and spectral resolution, but increases signal-to-noise ratio considerably. The implementation of mode 16x74 is the most critical due to the short time available to complete all the operations (TR = 100 ms). For this reason the Pattern Generator provides two values for the pixel readout frequency: f slow= 500 kHz when the pixel voltage has to be digitized and ffast = 4 MHz when the pixel is simply read from the CCD output register without any digital conversion. SWIR Spectrograph ----------------- The IR channel is constituted of a telescope and its fore-optics, a beam splitter and two spectrometers, each with its detector array actively cooled. The telescope is a Cassegrain type one with a 200 mm focal length, a f/4 aperture, leading to a 1.2 mrad (4.1 arcmin) IFOV, and a 15 arcmin free field of view (including the positioning tolerances). The distance between the primary and the secondary mirrors is 51 mm; that between the secondary mirror and the image plane is 82 mm. In front of the telescope, a fore-optics system has the primary goal of providing a cross-track scanning of the IFOV. It includes two mirrors, a moving and a fixed one. The total scanning angle is +/- 4.4 degrees (FOV = 128 IFOV), and is adjusted to the OMEGA viewing direction. The control of the scanning mechanism is performed by a dedicated FPGA-based electronic sub-system. Focused by the telescope on an entrance slit, through a shutter, the beam is first collimated, then separated, by a dichroic filter with its cut-off wavelength at 2.7 micrometres towards two spectrometers, operating in the following spectral ranges: 0.93 to 2.73 micrometers and 2.55 to 5.1 micrometers. Each spectrometer includes a blazed grating working at its first order, and an optical reflective system, then a field mirror and a refractive refocusing system which gives a large aperture on the detection block (f/1.6): it images the spectrum onto a 128 elements InSb linear array, cooled down a temperature of < 80K, and multiplexed by a charge transfer device. Sets of filters are implemented in front of the detector to reject the contribution of other orders from the grating. The InSb photodiodes have been manufactured by SAT. The dimensions of each photosensitive element is 90 micron x 120 micron, with a pitch of 120 micron. All elements of the focal planes are hybridized on a ceramic with two electric circuit layers to connect the elements together. The ceramic is glued on a titanium base plate and covered with a titanium closure, which includes the filters. An internal calibration source is implemented, to control potential shifts of the overall spectrometer transmission, and to calibrate the relative response of each pixel. It is made of a tungsten lamp, operated as a black body which can be power heated at different temperatures. The calibration beam is reflected towards the spectrometer by diffusion on the back side of the entrance slit. SWIR requires an accurate thermal control, at three levels: - the IR detectors must be cooled down a temperature of < 80 K, controlled with an accuracy better than 0.1K. This is done by connecting them (copper heat link) to two cryocoolers, one for each array: they consist in Inframetrics 13000 series integral Stirling cycle coolers. Their guarantied lifetimes are > 2500 hours. They are controlled by a dedicated electronics; - the spectrometer must be cooled down to 190 K, in order both to allow the detectors to reach their required operational temperature (< 80 K), and to minimize the thermal background. This is achieved by conductive coupling (heat pipes) to a “low temperature” radiator, provided by the S/C; - the electronics and the cryocoolers heads must be coupled (copper links) to a “high temperature” (280 K) radiator to dissipate their energy. OMEGA-ME Unit ------------- The OMEGA main electronics is designed to power and control the instrument, to acquire and compress all scientific data on line, and to interface with the S/C telecommand/telemetry system. The entire system is cold redundant. Within OMEGA-ME, the Command and Data Processing Unit(CDPU) has the following tasks: - acquisition of all scientific data from VNIR and SWIR; - formatting for real time data compression - wavelet based data compression, followed by formatting of processed data - reception and formatting of HK data - forward all data to the S/C telemetry system The CDPU is based on a TSC21020 Temic processor, and integrated, together with a 6Mbyte SRAM, into a 3D packaged highly miniaturized cube, inherited from a ÇIVA/Rosetta development." INSTRUMENT_TYPE = "IMAGING SPECTROMETER" END_OBJECT = INSTRUMENT_INFORMATION OBJECT = INSTRUMENT_REFERENCE_INFO REFERENCE_KEY_ID = "BIBRINGETAL2002" END_OBJECT = INSTRUMENT_REFERENCE_INFO END_OBJECT = INSTRUMENT END